The shrinkage of thermoformed plastic

Jan 10, 2025 Leave a message

In thermal forming, shrinkage refers to the change in size of a thermoplastic sheet or molded part under heat without the action of any mechanical stress.
Shrinkage testing of the material is recommended before the material is thermoformed.
① Accurately measure and record a piece of 200mm>200mm sheet, mark the extrusion direction with an arrow and record the cutting direction.
② Heat the oven to the temperature of sheet forming.
③ Put the sheet into the oven, in order to measure, it is necessary to cover a piece of wood with a layer of PT-FE film (such as Telflon or Hostaflon), then spray with talc powder, then place the sheet on it, and spray talc again, and finally cover it lightly with PTFE film. The film can be fixed to the edge of the board with a thumbtack.
④ The sheet shall be left in the oven for at least 30min, and the time of placing shall be increased by 5min for every 1mm increase in sheet thickness.
⑤ Remove sheet from oven and cool.
⑥ Measure sheet size after cooling, sheet shrinkage can be obtained by the following formula:
Shrinkage rate %= [(size before test, size after test) ×100] / size before test

In order to measure the anisotropy of the material, it is recommended to measure the longitudinal and transverse shrinkage of the material. If the newly supplied molding material has problems such as pleating, cracking at the clamp, and severe shrinkage at the contact heated joint, the shrinkage ratio should be tested with the new and old materials. The two materials require different processing parameters because they have different shrinkage rates and exhibit different behaviors during thermoforming.
Shrinkage of a thermoformed product can be obtained by comparing the difference between the size of the product and the corresponding mold.
Thermal shrinkage includes process shrinkage (VS), post shrinkage (NS) and total shrinkage (GS), and there are differences among them. Machining shrinkage can be calculated by:
Processing shrinkage rate VS % = [(mold size a thick product size) ×100] / mold size
Mold and product dimensions should be determined under the same conditions, such as at 23°C 24 hours after thermoforming.
After the processing of plastic products, at room temperature conditions, after a period of time can be found to have post-shrinkage. If the thermoformed product requires further processing, such as foam filling, then it is necessary to know exactly the value of the shrinkage after the material, so that the molded product can be accurately matched with the other mold. The total shrinkage value is:
Total shrinkage value (GS) = machining shrinkage value (VS) after ten years (NS)
Unfoamed ABS/PVC sheets will shrink after 5 days after thermoforming, and both suppliers and consumers must know the shrinkage behavior of the material and its processing sequence, because the cost and quality of the material will fluctuate accordingly.
Particular attention is paid to the problem of determining the dimensions of the die, trimming die and some other cutting dies on the thermoforming line. Because the product will not immediately complete the thermal shrinkage after the hot forming, the molded product is still warm when the edge is trimmed, the size of the cutting tool used must be precisely determined, and it is best that the individual parts of the cutting mold can be adjusted according to different materials.
Table 2-4 lists the shrinkage values of various plastics. These are only reference values, they also have a lot to do with the processing conditions. For plastics with a wide distribution of shrinkage values, to get the correct thermal shrinkage value, you should either ask the manufacturer of the material or test it before thermoforming. Accurate thermal shrinkage values can only be obtained by testing on thermoforming molds of similar geometric sizes. For molded products with high dimensional tolerances, the mold for which the prototype is manufactured must be tested, and the shrinkage of the various parts must also be determined.
The most important factors related to shrinkage: the type of plastic, cost fluctuations must also be considered; High cooling rate reduces processing shrinkage; Higher demoulding temperature will produce greater shrinkage than lower demoulding temperature. High draft equals low shrinkage in most cases; The production conditions of the forming material are granulation with different extruders, or the same extruder has different processing parameters, the production of the forming material may have different shrinkage behavior; The contraction of the positive mold is smaller than that of the negative mold. Under the same conditions, the maximum range of shrinkage fluctuation of molded products with the same material is 10%.
Note: The test site and/or the test method itself of the product for which shrinkage measurement is to be performed should be selected to ensure that no deformation occurs at the time of testing and that the product tolerance of less than 10% of the shrinkage value is not possible.